Zm-t6 Controller Manual ✦

Search for "ZM-T6" (or "ZM-X6") in your device's Bluetooth settings and select it.

To exit: Wait 10 seconds or turn unit off.

Ensure the battery is charged at least once every few months if stored for long periods to preserve battery health. m.media-amazon.com troubleshooting steps for a specific device or a guide on setting up the ShootingPlus V3 app for button mapping? zm-t6 controller manual

Press and hold the buttons simultaneously for 2 seconds. LED1 will flash rapidly. Select "T6" or "Gamepad" from your phone's Bluetooth list. LED1 will stay lit once connected. 🍎 iOS Connection (MFi Mode) Enable Bluetooth on your iPhone or iPad. Press and hold the B + Home buttons for 2 seconds. LED4 will flash rapidly. Look for "Xbox Wireless Controller" or " " in settings and pair. 💻 PC / Laptop Connection

. (Note: Compatibility may vary by iOS version; some newer firmware requires the ShootingPlus V3 app for button mapping). Search for "ZM-T6" (or "ZM-X6") in your device's

: Connect the micro-USB cable; the charge LED will light up.

| Code | Function | Options | Recommended Setting | | :--- | :--- | :--- | :--- | | | Temperature Sensor Mode | In (Internal/Air only) Out (External/Floor only) AL (Internal & Floor limit) | AL (to prevent floor overheating) | | P02 | Heating Difference (Hysteresis) | 0.5°C – 2.5°C | 1.0°C (prevents rapid switching) | | P03 | Floor Temp Limit (High) | 20°C – 50°C (or OFF) | 35°C for tile; 27°C for laminate | | P04 | Floor Temp Limit (Low) | 5°C – 15°C | 5°C (Anti-freeze mode) | | P05 | Temperature Correction | -9°C to +9°C | Use if sensor reads wrong (e.g., +2 if feels cold) | | P06 | Child Lock | 0 (No) / 1 (Yes) | 0 (Set to 1 to lock permanently) | | P07 | Weekly Schedule Enable | 0 (Off - Manual only) 1 (5+2 days) 2 (7 days) | 2 (Full weekly control) | | P08 | Temperature Unit | 0 (Celsius) / 1 (Fahrenheit) | 0 | | P09 | Backlight time | 0-30 seconds | 10 | | P10 | Deadband for Boiler | 1°C – 5°C | 2°C | | P11 | Dry Contact Select | 0 (NO) / 1 (NC) | 0 | | P12 | Factory Reset | Press Menu for 10s | N/A | Select "T6" or "Gamepad" from your phone's Bluetooth list

This comprehensive guide serves as your definitive . Whether you are installing a new system from scratch or replacing a burnt-out controller, this article will walk you through the wiring diagram, function settings, and common troubleshooting steps to get your vehicle moving.

| Terminal Label | Standard Function | Wire Color (Typical) | | :--- | :--- | :--- | | | Neutral Input (Power in) | Blue or White | | 2 (L) | Live Input (Power in) | Brown or Black | | 3 (NO) | Normally Open (Load output to heater) | Black (Load) | | 4 (COM) | Common relay terminal | Connect to Live (L) via jumper | | 5 (N2) | Neutral output to Heater | Blue (Load) | | 6 (Sensor) | Floor sensor pin 1 | Red/White (Probe) | | 7 (Sensor) | Floor sensor pin 2 | Yellow/Black (Probe) |

If your PC does not have Bluetooth, you must use a 2.4G wireless dongle or a direct USB cable connection. In wired mode, the controller is often recognized as a "ShanWan Xbox 360" controller for Windows.